onlyfire 14431 Universal Spark Generator Replacement for Gas Grill Models by Broil-Mate and Others, 2 Male Outlet AA Battery Push Button Igniter

Needed a replacement ignitor for a ProComm / Feature Comforts propane ventless heater model MD300TBE (in owners manual also listed for MD100TBE and MD200TBE). Original ignitor part model number is DHLG-12 dated 2010, 1.5V DC. Yes, got money's worth out of this original part, over twelve years strong. Clicker stopped clicking from previous attempts to clean battery corrosion off. Looked up part at ProComm heater site and the current ignitor part number is PIMSC1-01 but out of stock. Took a chance on this one and it fits. Important to know is the hole to accept the ignitor on the heater has to be approximately 3/4 of an inch across to fit ignitor into hole. If hole is smaller, then may need to file down edge on heater a little to fit. This fit our propane heater fine with no adjustment. If you open the heater and the ignitor looks similar this should work. We bought the one plug model. The ignitor block has a flat square plug end embedded in the bottom corner. The thin wire on the heater is round looking, but it still fits on a blade end. The ignitor plug blade must be aligned with the seam in the wire plug. The existing wire on the unit looks like a round end but fits on a flat square blade. Did not think it would fit, but looked at original part blade and it is the same as new part, flat blade. Blade aligns with seam then slips on. Round wire end to square, works. For heater install. Took the screws off face of heater, unscrewed the old ignitor part, pulled off wire, positioned the new ignitor in heater hole, spun on the included plastic nut, dropped in a AAA battery, put the rubber cap on it and now clicks away like normal. This was a good price and with prime was delivered next day. Now if it lasts as long as the original then great. Just remember to take out the batteries when not in use for the season or occasionally check for leaky batteries. Hope those with a propane heater find this helpful since this is advertised mostly for bbq grills. It just basically clicks to make a spark to ignite the pilot light.

I got this to replace an ignitor on my ProComm propane/natural gas heater. I read a review that it fit another ProComm so gave this a try. It arrived and was slightly bigger than the one that failed. I think the secret on sizing is the battery. If you have a "AA" this is your pick, if you have a "AAA" this will be too big (I had a "AAA"). Rather than send back due to my miss estimation, I used a file to increase the mounting hole by about 1/16" all around. It fit fine after that and the 2 ignitor wires fit perfect. Once that battery was installed, it worked perfect.

As the Hemptons stated it is not exact fit. Make sure you measure the diameter of mounting hole in your grill before you order. Luckily I have a step drill that I was able to widen the hole. Other than that it works great!

So my dog have bit off the button part of this which wouldn't allow me to create or generate the spark in there once I turned on the gas. So I had to get an extension lighter which is a pain in the butt, but overall it was necessary. I went to home Depot to see if I can buy something like this but they didn't have anything remotely close. You kind of have to work around it. Do your own little thing, but you're only able to like one grill at a time. So once I looked at Amazon I noticed that this device was available. It does come with three four even five or six prongs depending on your grill, at the time I did not know my girl had four because it has a side burner on the side which I don't use that much unless I'm doing like a ribeye steak. So I order the wrong one for my grill but it was okay because I didn't need or used the side grill. Very easy to hook up. You go ahead and take off the nut. Pull it from the back, disconnect all the cables and then connect them into your new setting. The only thing that I would say is make sure you remember where all the cables go. If you connect one of the cables that you're not going to be using then you're going to find yourself. One of the grills is not going to be working because of compatibility. So make sure you are aware of where each strand of electricity cable goes to on the grill. That way you turn on the one you want but that's only because I bought the one that wasn't for my grill. I was missing one. Therefore, I made the mistake to connecting one in the wrong place. I had to follow the line to see which was the one I needed. If you buy the right prong with the right number for your grill then you won't have this problem. Just connect all of them and it should work. I like the design, very simple plug and play and push it back into through its hole. Connect bolt with the button. Make sure you put the battery in there as well and everything works as new. I need to order a new one now this time to make sure that I get my five prongs. That way all my igniters work at the same time. Depending on how many igniters you need, the item itself is bigger or smaller, but because it's all sitting behind the grill face, you don't see it anyways. And you should have the amount of space you need for the burners that you have. Anyways. As far as look, I did go with the simpler look but I've noticed that they have a more modern look with the stainless steel. So depending on your knobs on your grill and if you want to match that same look, you can always upgrade to the better looking knobs but that's optional depending on what it is that you know you want to do. As far as working it shouldn't change anything. It is all she's visually aesthetically appealing.

The Onlyfire Spark Generator arrived quickly, well-packaged, and exactly as described. Installation was simple and straightforward. Quick swap out, no special tools or complicated steps required. Within minutes, my fireplace was sparking the flame and igniting like new. This little ignitor proved to be a quick, effective solution to what I thought might turn into a bigger repair project. If you need a reliable push-button igniter replacement that installs easily and works immediately, this is it, for sure!!!

Purchased this to put on my fireplace for sunroom and so glad I did. Was easy to install and works great. Saved me money not having to pay a repairman.

Perfect replacement, identical to the igniter on our gas logs. Prompt delivery and perfect operation.

Worked great. It is larger than the original. Good price!

Este producto no lo encontré en ninguna de las tiendas especializadas de boilers y aparatos similares en monterrey, en Amazon lo encontré y llego muy rápido. Funciona ala perfeccion

This is my second time buying this exact ignitor for different grills — both times it worked like a charm. It was easy to install (just needed a 7/8" hole) and connected quickly to standard burners. The spark is strong, and it lights up the BBQ on the first try every time. No battery included, so make sure to have a fresh AA on hand. For under $10, it’s a cheap fix that works just as well as the original part.

Five stars for selling a product that fits a AAA battery! The starter for the infrared on the BBQ was no longer functional, plus we somehow lost the rubber part, so we purchased this to replace it. After installing we realized that the disconnect connector was detached, so we headed to the car parts section of Canadian Tire to find the right replacement, connected that and soldered a bit, then added a shrink wrap tube to prevent erosion and connected to this part and voila! The infrared works perfectly!

I give it a 4 star because I just installed it so only time will tell if it's worth the value but it's working so far and it wasn't hard to install at all. Will let you know if it last through the summer cookouts .

Perfect fit. Works great.