Home Soft Things Hairpin Metal Table Legs 30 Inch Legs for Furniture Coffee Bench Dining End Industrial Table Desk Set of 4 with Screws Adjustable Cushion Black Floor Protectors, 30"

These 30" table legs were perfect. Well made and the Finnish looks great, also very sturdy. They were exactly as advertised and good quality. I would certainly recommend them to others. Thank you for a good sturdy product.

I wasn't sure what to expect for the price & these far exceeded my expectations. The "feet" are attached to the legs, much better than pop on ones. I find them to be sturdier with no wobble & the legs themselves are a perfect weight. These are being used to convert a sofa table to a coffee table & it will have 1/2" glass on top so having attached feet on well constructed legs will let me move the table easily. I'm a senior & very pleased with this purchase.

I had no trouble installing these legs, and they look great. I am not very handy, so, perhaps it will help you if I explain how I installed the legs.What I needed: Finished table top,, 16 lag bolts, nut driver, drill and drill bit, masking tape. Really, I needed all of this stuff! (Read 1 and 2 before going to the hardware).I used a pencil and a ruler too.1. I measured the thickness of my table top - I had finished a piece of Butcher Block.2. I took one of the table legs to the hardware store (I chose ACE) to purchase 16 lag bolts and a nut driver for the lag bolts. (To help you, they will need to know how thick your table top is. Your bolts (or screws) need to be shorter than the thickness of your table). I also asked what size bit might be the best. (If you need the bit and masking tape, don't forget that.)3. From the tip of the drill bit, I measured how deep I wanted the bolt to go into the table. I placed the tape on bit at that depth. (nope, not on the point, near the chuck that holds the bit in place. The point to the tape is how deep you want to drill - it is a measurement smaller than the thickness of the table top.)4. I used a pencil to mark where I wanted the leg (I put my legs about 1" inside the edges). I measured again.5. Holding the leg in place and being sure I was on my pencil line, I pulsed the drill into the hole with the taped bit until it was as deep as the masking tape marker. (After drilling just a little bit of the first hole, I verified that the bolt was going to be the right size for the hole)6. I put the lag bolt in place using the nut driver.7. I drilled and placed a second lag bolt in on the leg before drilling the last two holes for each leg and driving the bolts in place.I did go back and forth between the drill bit and nut driver several times. This might be a slower way to go, but I suffered no setbacks or errors. Even going very slowly, this only took 40 minutes.Thanks to those who recommended the nut driver. This job would have been difficult without.. The masking tape helped a lot too.By phone, the shipper recommended lag bolts for my 1.5 inch butcher block, although wood screws could be used. The lag bolts work very well and I am glad I used them.

These legs worked great for a table I built! The height is perfect! They were easy enough to install and the table is sturdy. There was 1 missing adjustable pad when I opened them so I just took them off the other 3 legs and everything functions fine.

Sturdy, great quality used them for end table legs on live edge walnut table use bough longer screws they came with were pretty short would buy again

Nice finish, works great, easy to install.

Just as described. Added these to the fireplace stand I purchased from Amazon because it was sitting too low. These legs definitely made a positive difference and are Esthetically Pleasing.

Nice hairpin legs for standard table height. We had a problem where one leg was damaged. See pic. Wasn't terrible but just that the mounting base of one leg was bent at one corner. We have to assume this is more of a shipping damage issue than a manufacturing issue. I flattened it back out with a hammer and everything is good to go. We plan to replace the leveler foot pads with something with pads of larger diameter and that pivot, but it's nice to have leveling feet so this is also great. Anyone looking to replace the feet, note that they are size 6mm x 1 screw threads.